Double Strap Hinges (3" Gap)
Central Eye (#8312)
EXTREMELY HEAVY DUTY
FABRICATED FROM 2” WIDE BY 1/4” THICK STEEL
3” BETWEEN STRAPS
3/4” EYE TO FIT OUR 3/4” PINS
HOT DIPPED GALVANIZED FINISH
OPTIONAL BLACK POLYESTER POWDER COAT OVER HOT DIPPED GALVANIZED FINISH (BPPCG)
SOLD INDIVIDUALLY OR IN SETS
Available in Hot Dipped Galvanized Finish or Black Polyester Powder Coat over Hot Dipped Galvanized (BPPCG)
DOUBLE STRAPS NOT ONLY HANG THE GATE, THEY STRENGTHEN AND SUPPORT THE GATE
|5" Double Strap for Gates up to 36" wide or bottom strap on Gates up to 10 feet wide|
|8312-652||5" Gal Double Strap||$16.70|
|8312-65SP||5" BPPCG Double Strap||$24.10|
|12" Double Strap for Gates up to 4 feet wide|
|8312-422||12" Galvanized Double Strap||$29.90|
|8312-42SP||12" BPPCG Double Strap||$45.50|
|18" Strap for Gates up to 7 feet wide|
|8312-482||18" Galvanized Double Strap||$33.50|
|8312-48SP||18" BPPCG Double Strap||$50.40|
|24" Double Strap for Gates up to 10 feet wide|
|8312-542||24" Galvanized Double Strap||$39.20|
|8312-54SP||24" BPPCG Doulbe Strap||$56.20|
BPPCG = Black Polyester Powder Coated over Hot Dipped Galvanized
|Bottom strap can be a 5" strp used with a 12", 18", or 24" strap on the top.
Adjustable bottom fitting (8250) can also be used with longer straps on the top.
|Hot Dipped Galvanized carriage bolts, washers, and nuts included. (Black touch up paint for heads of bolts available)|
|LINK TO 8312 CENTRAL EYE SET WITH 8800 PINS (GATE HUNG BETWEEN POSTS)|
|LINK TO 8312 CENTRAL EYE SET WITH 8317 PINS (GATE HUNG BEHIND POSTS)|
|LINK TO PRODUCT SPECS 8312 HINGES|
|GATE INSTALLATION CONFIGURATIONS|
|HUNG BETWEEN THE POSTS||HUNG BEHIND THE POSTS|
Typical between posts installation.
Typical Behind Posts Installation Gate overlaps the post by 0.5” to 1.0”. This method is used extensively in europe as the gate is fully out of the way when open. uses 8317 pins with square shaft to prevent the pins rotating.
|BETWEEN THE POSTS|
Gates hung between the posts can be hung on either a square or round post. Allow for a 5" space between the gate and the post (on hinge side) so that there is enough room for adjustment when it is necessary. The commonest pin used for this type of installation is the full threaded with nut and washer on either side of the post (#8800-002). Do not forget to leave the space at the other end of the gate to accommodate the kind of latch that is being used.
BEHIND THE POSTS
If the gate is hung behind the posts the gate is constructed so it is at least 1" wider than the opening between the posts. Square posts are recommended. Pins with square shaft (#8317-022) should be used to prevent pin rotation along with the Adjustable Bottom Fitting, which allows for easy adjustment of the gate height at the latch end. There are several advantages which include:
|LINKS TO PRODUCT INFO & RELATED PRODUCTS|
|PRODUCT SPECIFICATIONS (8312 HINGES)|
|DOUBLE STRAP INDEX PAGE|
|SINGLE STRAP HINGES|
Snug Cottage Hardware offer an extensive selection of FREE gate plans and instructions for strudy ranch gates, rail gates, doulbe drive gates, and dumpster enclosure gates. Click the lind above and follow the steps.
Of course our staff is available to answer your questions at firstname.lastname@example.org